这篇文章上次修改于 233 天前,可能其部分内容已经发生变化,如有疑问可询问作者。

1、安装宝塔

当前使用版本为宝塔7.5.1
(https://www.bt.cn/bbs/thread-19376-1-1.html)
执行:
yum install -y wget && wget -O install.sh http://download.bt.cn/install/install_6.0.sh && sh install.sh

2、安装Xray

当前使用版本为Xray1.3.0
https://github.com/XTLS/Xray-install

安装:
bash -c "$(curl -L https://github.com/XTLS/Xray-install/raw/main/install-release.sh)" @ install

(卸载:
bash -c "$(curl -L https://github.com/XTLS/Xray-install/raw/main/install-release.sh)" @ remove --purge

2.1、Xray相关目录

installed: /usr/local/bin/xray
installed: /usr/local/etc/xray/config.json

installed: /usr/local/share/xray/geoip.dat
installed: /usr/local/share/xray/geosite.dat

installed: /var/log/xray/access.log
installed: /var/log/xray/error.log

installed: /etc/systemd/system/xray.service
installed: /etc/systemd/system/[email protected]

3、配置宝塔

3.1、一键安装LNMP:
77598-yk7obq3a0s.png
3.2、宝塔面板上添加虚拟机:ip.xxx.xyz
3.2.1 如下图:
00921-ub8buzljmtp.png
3.3 申请SSL:
3.3.1如下图:
62774-dma4195nvht.png
18593-y1jypqtvprb.png

3.4 配置虚拟机Nginx

(在server最后的大括号前}添加以下内容)

#V2ray代理
location /abc123/ {   # /abc123/为伪装目录
  #如果不是websocket请求
  if ( $http_upgrade != "websocket" ) {
    rewrite ^/(.*)$ /;
  }
  proxy_redirect off;
  proxy_pass http://127.0.0.1:12345;   # 12345为Xray对应的端口
  proxy_http_version 1.1;
  proxy_set_header Upgrade $http_upgrade;
  proxy_set_header Connection "upgrade";
  proxy_set_header Host $host;
  proxy_read_timeout 300s;
    # Show real IP in v2ray access. log 
    proxy_set_header X-Real-IP $remote_addr; 
    proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for;
}

3.3.1、如下图:
58733-k1btqql44h.png

4、配置Xray(VLESS)

Xray配置文件位置:/usr/local/etc/xray/config.json

{
    "inbounds": [
     {
        "port": 12345,
        "listen": "127.0.0.1",
        "protocol": "vless",
        "settings": {
            "decryption": "none",
            "clients": [
                {
                "id": "619f16e1-c052-4eed-9e0a-05b5d5f60e9d",
                "level": 0
                }
              ]
        },
        "streamSettings": {
            "network": "ws",
            "wsSettings": {
                "path": "/abc123/"
            }
        }
    }],
    "outbounds": [{
        "protocol": "freedom",
        "settings":{}
    }]
}

5、Xray服务端相关

启动:systemctl start xray/usr/local/bin/xray run -config /usr/local/etc/xray/config.json
重启:systemctl restart xray
停止:systemctl stop xray
更新geoip.dat和geosite.dat:
bash -c "$(curl -L https://github.com/XTLS/Xray-install/raw/main/install-release.sh)" @ install-geodata
随系统启动:systemctl enable xray

6、配置客户端

以windows使用v2rayN为例
6.1、添加VLESS服务器
6.2、配置如下图:
48471-0f8mmfqmjnhj.png

7、如无异常,则能正常使用。
7.1、如不能使用,检查服务端配置/usr/local/etc/xray/config.json及客户端配置是否一致。
7.1.1、有可能上述安装的软件版本都已更新。本方法可能失效。

1